Vlan 삭제 명령어 - Vlan sagje myeonglyeong-eo

[ 스위치 모드 변경하기 ]

① Switch>enable ☞ 유저모드(User Mode) ② Switch#config terminal ☞ 프리빌리지 모드(관리자모드)

③ Switch(config)#interface fastethernet 0/1 ☞ 구성모드(configuration mode)

④ Switch(config-if)# ☞ 인터페이스 구성모드

⑤ Switch(config-if)#exit -> 빠져나가기

⑥ Switch(config)#exit ⑦ Switch# exit ⑧ Switch> enable

⑨ Switch# show interface status -> 포트별 상태를 알아보기 ( 명령어는 반드시 관리자모드에서

입력해야한다.)

⑩ Switch# show ? -> show 다음 입력할 수 있는 명령어 모음 표시

⑪ Switch# show interface ?

⑫ Switch# show interfaces -> 각 포트의 설정보기 ⑬ Switch# show interface -> 각 포트의 설정보기

[ 포트설정 바꾸기 ]

① Switch>enable ② Switch# configure terminal

③ Switch(config)# interface fastethernet 0/1

④ Switch(config-if)# speed 100 -> 속도를 100M 로 설정

⑤ Switch(config-if)# duplex full -> 전송방식을 전이중으로 설정

⑥ Switch(config-if)# exit -> 구성모드로 가기 ⑦ Switch(config)# exit -> 관리자 모드로 가기

⑧ Switch# show interface status

⑨ Switch# show interface fastethernet 0/1 (speed {auto | 100 | 10 } duplex {auto | half | full} )

1 번 포트를 속도(대역폭)은 100Mbps, 통신방식은 Full-duplex ,2 번 포트를 속도(대역폭)은 10Mbps,

통신방식은 half-duplex 로 설정하시오.

[ hostname 설정하기]

① Switch#config terminal ② Switch(config)# hostname atom 또는 hostname 노무현

노무현# //atom 은 이름이므로 다른 이름을 마음대로 사용할수 있다.

[ secret 암호설정하기]

① Switch# config terminal

② Switch(config)# enable secret atom123 //암호는 자유롭게 지정할 수 있다.(암호는 구성모드에서

지정한다)

③ Switch(config)# exit ④ Switch# exit

Switch> enable

Password: ******

Switch# // 이제는 암호를 넣어야 관리자모드로 들어갈 수 있다.

[ 스위치에 IP 주소 설정하기 ]

① Switch> enable ② Switch# config terminal

③ Switch(config)# interface vlan 1 ④ Swtitch(config-if)# ip address 192.168.100.1 255.255.255.0

⑤ Switch(config-if)# exit ⑥ Switch(config)# exit

⑦ Switch# show interface vlan1 또는 vlan 1

[ 기본 게이트웨이 설정하기 ]

① Switch# config terminal ② Switch(config)# ip default-gateway 192.168.0.1

③ Switch(config)# exit ④ Switch# show running-config // 현재 스위치에 설정된 모든 내용 보여주기

[ 암호 삭제하기 ] ① Switch(config)# no enable secret password 지정한 암호

[ 라우터 명령어 집합 ]

Router>enable (사용자모드에서 관리자모드로 전환하기)

[현재 사용하고 있는 구성파일 보기-RAM]

Router# show running-config 또는 write terminal

[NVRAM 에 저장된 구성파일 보기]

Router# show startup-config

[현재 구성을 NVRAM 에 저장하기]

Router# write memory 또는

copy running-config startup config

[ 플래시 메모리 정보보기 ]

Router# show flash

[ 라우터의 현재정보 보기 ]

Router# show version

[ 인터페이스 정보보기 ]

Router# show interface

[ 이더넷 인터페이스 0 번 보기 ]

Router# show interface ethernet 0

[ 라우터 CPU 사용률 보기 ]

Router# show processes cpu

[ 라우터 메모리 상태 보기 ]

Router# show memory

[ 구성모드로 들어가기 ]

Router# configure terminal

Router(config)# CTRL + P -> 명령어 히스토리 단축키

[ 라우터의 이름과 enable secret , enble password 설정하기 ]

Router(config)# hostname CISCO-2500

CISCO-2500(config)# enable secret cisco

CISCO-2500(config)# enable password seoul

CISCO-2500(config)# exit

CISCO-2500# exit

CISCO-2500> enable

Password: secret 암호가 설정되어있으면 secret 를 넣는다. 암호는 대소문자 구분합니다.

CISCO-2500# show running-config (현재 설정된 구성정보보기)

secret 암호와 패스워드 암호가 보인다.

[ 텔넷 접속 패스워드 설정하기 ]

CISCO-2500> enable

Router#> configure terminal

Router(config)# line vty 0 4

Router(config-line)#login ( 라인구성모드 )

Router(config-line)#password korea

Router(config-line)# exit

Router(config)#

[ 인터페이스 구성모드 들어가서 이더넷에 IP 주소 할당하기 ]

Router# configure terminal

Router(config)# interface ethernet 0

Router(config-if)# no shutdown ( 인터페이스 살리기 )

Router(config-if)#ip address 211.23.156.30 255.255.255.224

Router(config-if)# exit

Router(config)# exit

[ 시리얼 인터페이스 설정하기 ]

Router# configure terminal ( 구성모드로 들어가기 )

Router(config)# interface serial 0

Router(config-if)# no shutdown

Router(config-if)# ip address 10.123.51.41 255.255.255.252

Router(config-if)# exit

Router(config)# exit

Router# show running-config (현재 구성설정보기 )

ethernet 0 에 할당된 IP 주소를 확인한다. 텔넷에 할당된 암호를 확인한다.

Router# show interface ( 현재 인터페이스 보기 )

이더넷 0 가 up 으로 설정되어 있는지 확인한다.

[ 라우팅 프로토콜 설정하기 ]

Router> enable

Router# config terminal

Router(config)# router igrp 100

Router(conifg-router)# network 211.23.156.0

Router(conifg-router)# network 10.0.0.0

Router(conifg-router)# Ctrl+Z(exit) ( 프리빌리지모드로 나가기)

Router# show running-config ( 구성파일 보기 )

[RAM 의 구성파일을 NVRAM 에 저장하기]

Router# copy running-config startup-config

[ 플래시 메모리 내용보기 ]

Router# show flash

[IOS 이미지 파일을 TFTP 서버로 백업하기]

Router# copy flash tftp

[ TFTP 서버에서 플래시메모리 IOS 파일 복원하기 ]

Router# copy tftp flash

[ 라우터의 구성파일 백업하기 ]

Router# copy startup-config tftp

[라우터의 구성파일 복원하기]

Router# copy tftp startup-config

[ 라우팅 테이블 보기 ]

Router# show ip route

[ 스태틱 라우팅 구현하기 ]

Router# configure terminal

Router(config)# ip route 210.162.65.0 255.255.255.0 203.155.10.2 1

Router(config)# exit

Router# show ip route

[ 디폴트 라우팅 설정하기 ]

Router>enable

Router# configure terminal

Router(config)# interface ethernet 0

Router(config-if)# ip address 211.23.123.1 255.255.255.0

Router(config-if)# exit

Router(config)# interface serial 0

Router(config-if)# ip address 61.105.112.41 255.255.255.252

Router(config-if)# exit

Router(config)# ip route 0.0.0.0 0.0.0.0 61.105.112.42

Router(config)# exit

Router# write

Router#